eng Русский язык

Interplate Zero

A two pack, heat resistant, water based shop (pre-construction) primer providing good corrosion protection and resistance to damage caused by welding, gas cutting and fairing. Suitable for fast welding processes and offers control of secondary surface preparation requirements.

Intended uses

As a shop (pre-construction) primer for the protection of steel during fabrication and assembly. Suitable for use with controlled cathodic protection. For use at Newbuilding.

color ZER010/ZER011-Grey, other colours available upon request
Finish/Sheen Matt
Part B (Curing Agent) ZER011 (Powder)
Volume Solids 36% ±2% (ISO 3233:1998)
Mix Ratio 5.34 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness 15 microns dry (42 microns wet)
Theoretical Coverage 24.00 m2/litre at 15 microns dft, allow appropriate loss factors
Method of Application Airless Spray, Brush, Conventional Spray, Roller
Flash Point Not applicable

Drying Information

  Substrate Temperature
  5°C 10°C 25°C 35°C
Hard Dry [ISO 9117:90]     4 mins 2 mins
Pot Life

 

  24 hrs 24 hrs

Overcoating Data

Note.

Consult International Paint, minimum of 7 days for appropriate primers.

Regulatory data

VOC

0 g/lt calculated 0 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)

Note.

VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.

Certification

When used as part of an approved scheme, this material has the following certification:

  • Weld Fumes - Trace Gas Measurement during Welding (SLV)
  • Weld Quality - Approved for Overweldable Shop Primers (GL)
  • Weld Quality - Approval of Prefabrication Primers (LR)
  • Weld Quality - Shop Primers for Corrosion Protection of Steel Plates and Structures (DNV)
  • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))
  • Fire Resistance - MSC61(67) Smoke & Toxicity (WFR)
  • Fire Resistance - Marine Equipment Directive compliant

Consult your International Paint representative for details.

System and compatibility

Consult your International Paint representative for the system best suited for the surfaces to be protected.

Surface preparations

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

NEWBUILDING

Shop primers should be applied using automatic blasting/spraying equipment. Blast to a minimum of Sa21⁄2 (ISO 8501-1:2007). Consult your International Paint representative for specific recommended abrasives and surface profiles.

Apply Interplate Zero before oxidation occurs. If oxidation does occur the entire oxidised area should be reblasted to the standard specified above. Ensure that the area is clean and dry prior to application of Interplate Zero.

Consult your International Paint representative for specific recommendations.

APPLICATION

Mixing

Material is supplied in 2 separate containers as a unit. Always mix a complete unit in the proportions supplied.Agitate the binder (Part A) with a power agitator then slowly add the powder (Part B) whilst continuing agitating.Where product is supplied as a 17.8 litre unit it will be necessary to transfer Part A to a separate suitable container prior to adding Part B.Allow to mix for at least 5 minutes, sieve through a 30-60 mesh screen before use. Continue stirring during use. Always add Powder to Binder.

Thinner

Not recommended. Consult your International Paint representative.

Airless Spray

Recommended Tip Range 0.38-0.58 mm (15-23 thou) Total output fluid pressure at spray tip not less than 60 - 100 kg/cm2 (850 - 1420 p.s.i.)

Conventional Spray

Recommended.

Brush

Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Roller

Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Cleaner

Potable Water.

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with potable water. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units, to ensure that the potlife has not been exceeded. Clean all equipment immediately after use with water. Spray equipment requires flushing with water. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency will depend upon factors such as amount sprayed, temperature and elapsed time including work stoppages. Monitor material condition. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Welding

Hot Work In the event welding or flame cutting or fairing is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

SAFETY

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

Limitations

Drying times will depend on the substrate temperature and ventilation conditions. If the relative humidity is below 50%, cure will be retarded. Interplate Zero is not recommended for manual spray application. At higher dry film thickness, fabrication properties (welding and cutting) may be affected. Shop primers are not recommended for use as touch-up primers after fabrication.

Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. The temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C , unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with the information given in the STORAGE section of this data sheet.

Unit size

Unit size Part A Part B
  Vol Pack Vol Pack
17.8 lt 15 lt 15 lt 2.8 lt 20 lt

Part A is supplied in a polyethylene container
Part B is supplied in a steel container For availability of other unit sizes consult International Paint

Unit shipping weight

Unit size Unit Weight
17.8 lt 31.01 Kg

Storage

Shelf Life Cool dry conditions Part A must be kept above 5°C
Part A - 9 months maximum from date of manufacture at temperatures up to 25°C. Part B - 18 months minimum from date of manufacture at temperatures up to 25°C. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Яндекс.Метрика