Intersmooth 360 SPC

INTENDED USES

Specifically designed for Coastal Vessels.
For use at Maintenance & Repair.

color	BEA361-Black, BEA362-Blue, BEA368-Dark Brown, BEA369-Dark Red, BEA387-Brown
Finish/Sheen	Not applicable
Part B (Curing Agent)	Not applicable
Volume Solids	40% ±2% (ISO 3233:1998)
Mix Ratio	4.5 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness	Range: 70 - 140 microns dry (175 - 350 microns wet) may be specified depending upon end use.
Theoretical Coverage	Range: 5.7 - 2.9 m²/litre at 70 - 140 microns dft, allow appropriate loss factors
Method of Application	Airless Spray, Brush, Roller
Flash Point	Single Pack 22°C (Product produced and supplied in North America has a flashpoint of 21°C due to locally sourced solvents. There is no detrimental effect on product performance.)

Drying Information

	Substrate Temperature
	-5°C	5°C	25°C	35°C
Touch Dry [ISO 9117/3:2010]	2 hrs	60 mins	40 mins	30 mins
Before Flooding	30 hrs	18 hrs	12 hrs	10 hrs

Overcoating Data

see limitations

Overcoated By	Substrate Temperature
	-5°C		5°C		25°C		35°C
	Min	Max	Min	Max	Min	Max	Min	Max
Intersmooth 360 SPC	12 hrs	28 days	6 hrs	28 days	4 hrs	28 days	3 hrs	28 days

 

REGULATORY DATA

VOC 518 g/lt as supplied (EPA Method 24) 343 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)

Note.

VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.

EPA

USA Federal EPA Registration No. 2693-187 This product is not registered in Canada. See Page 4 for additional Regulatory Data.

This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26).

 

 

CERTIFICATION

When used as part of an approved scheme, this material has the following certification:
Product recognised by the following classification societies as compliant with the International Convention on the
Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001):
• Lloyds Register
• Germanischer Lloyd
• Korean Register of Shipping
• Det Norske Veritas
• Bureau Veritas
Consult your International Paint representative for details.

SYSTEMS AND COMPATIBILITY

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

SURFACE PREPARATIONS

Abrasive blast clean to Sa2 (ISO 8501-1:2007). A blas

MAJOR REFURBISHMENT

Intersmooth 360 SPC should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intersmooth 360 SPC must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Intersmooth 360 SPC

REPAIR

Application of Intersmooth 360 SPC over self:
Clean the entire area with close high pressure fresh water washing using a fan-jet lance held close to the surface (3,000 p.s.i., 211 kg/cm²) as soon as the vessel enters dock and before it dries out. Consult International Paint for alternative methods of surface preparation. Repair corroded areas with the recommended anticorrosive primer system and apply Intersmooth 360 SPC within the overcoating interval specified for the primer (consult relevant primer data sheets).

Application of Intersmooth 360 SPC over International Paint TBT-Free, International Paint Intersmooth SPC or competitors antifoulings: Consult your International Paint representative for specific recommendations.

 

APPLICATION

Mixing

This material is a one pack coating. Always mix thoroughly with a power agitator before application.

Thinner

Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Recommended
Tip Range 0.46-0.66 mm (18-26 thou)
Total output fluid pressure at spray tip not less than 211 kg/cm² (3000 p.s.i.)

Conventional Spray

Application by conventional spray is not recommended.

Brush

Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Roller

Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Cleaner

International GTA007

Work Stoppages and Cleanup

Thoroughly flush all equipment with GTA007. All unused material should be stored in tightly closed containers. Partially filled containers may show surface skinning and/or a viscosity increase of the material after storage. Material should be filtered prior to use.

Welding

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

SAFETY

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

LIMITATIONS

Coating lifetime is directly proportional to thickness applied. Performance of the product is dependent upon the specified film thickness being achieved.
On immersion, Intersmooth 360 SPC will exhibit a slight colour change.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

ADDITIONAL REGULATORY DATA

Refer to container label for information concerning Precautionary Statements, Directions for Use and Storage and
Disposal.