eng Русский язык

Intershield 6GV

A Low Solar Absorbing, high solids, extended durability, epoxy non-skid deck coating. Developed to meet the requirements of MIL-PRF-24667C Types I, II and V, Composition G.

Intended uses

Wherever a rollable, extended durability, Low Solar Absorbing, non-skid deck coating is required. For use at Newbuilding, Maintenance & Repair or On Board Maintenance.

color EGA650-Dark Grey
Finish/Sheen Flat
Part B (Curing Agent) EGA651
Volume Solids 90% ±2% (ASTM D2697-86)
Mix Ratio 3 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness Not applicable
Theoretical Coverage 0.49-0.73 m2/litre, allow appropriate loss factors
Method of Application Roller
Flash Point Part A 39°C; Part B 39°C; Mixed 39°C
Induction Period Not applicable

Drying Information

  Substrate Temperature
  10°C 23°C 35°C
Hard Dry [ASTM D1640 7.7] 24 hrs 12 hrs 9 hrs
Pot Life 2 hrs 60 mins 30 mins

Overcoating Data

Overcoated By Substrate Temperature
  10°C 23°C 35°C
  Min Max Min Max Min Max
Interthane 990 24 hrs 72 hrs 12 hrs 72 hrs 9 hrs 72 hrs
Interthane 990HS 24 hrs 72 hrs 12 hrs 72 hrs 9 hrs 72 hrs

Regulatory data

VOC

92 g/lt (0.77 lb/US Gal) as supplied (EPA Method 24)

Note.

VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.

MIL SPEC

Non-Skid MIL-PRF-24667C, Types I, II & V, Composition G

System and compatibility

Consult your International Paint representative for the system best suited for the surfaces to be protected.
TYPICAL SYSTEMS:

  • Intershield 456/Intershield 6GV
  • Intershield 456/Intershield 6GV/Interthane 990
  • Intershield 456/Intershield 6GV/Interthane 990HS

Surface preparations

Paint only clean, dry surfaces. Remove all grease, oil, soluble contaminants and other foreign matter by "solvent cleaning" (SSPC-SP1).

Intershield 6GV is designed specifically for use as a rollable non-skid deck coating over properly prepared Intershield 456. Consult the relevant product data sheets for surface preparation and overcoating information. Consult your International Paint representative for specific recommendations.

APPLICATION

Apply by smooth phenolic core roller cover to achieve 'ploughed field' effect if required. Consult International Paint for other effects. Apply mixed material by pouring a small amount onto the properly prepared surface. Then spread out an even amount and texture with a long handled, smooth phenolic core roller cover. Heavy, or thick, carelessly applied coats will be subject to mudcracking and/or blistering. When Intershield 6GV has been properly applied the surface will present a uniformly rough appearance over the entire surface. There will be no loosely bound clumps of particles. If required the surface profile can show a pattern of hard raised peaks or ridges similar to a "ploughed field". The peaks of the ridges will be about 0.5 - 1.0" (12.5 - 25.0 mm) apart and approximately 1/16" to 3/32" (1.5 - 2.4 mm) high. The non-skid coating at its thinnest point should be at least 762 microns thick. Consult the following equipment recommendations:

Mixing

Do not proportion material and do not mix until ready to use. Material is supplied in one container as a unit. Always mix a complete unit in the proportions supplied. Agitate Intershield 6GV colour base material (Part A) with a power agitator for 2 minutes, ensuring that no compacted aggregate remains in the bottom of the can. Add Intershield 6GV converter (Part B) and mix thoroughly with a power agitator for 3 minutes stopping once to scrape the sides and the bottom of the can. Take care not to mix air into the material.

Thinner

DO NOT THIN !

Roller

Use a smooth phenolic core roller cover.

Cleaner

International GTA220/GTA415

Work Stoppages and Cleanup

Clean all equipment immediately after use with International GTA220/GTA415. Monitor material condition. Do not exceed pot life limitations.

Welding

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

SAFETY

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

Limitations

Apply in good weather when air and surface temperatures are above 10°C. Surface temperature must be at least 3° C above dew point. For optimum application properties, bring material to 21-27°C prior to mixing and application. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Technical and application data herein is for the purpose of establishing a general guideline of the coating and proper coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results actually found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

Unit size

Unit size Part A Part B
  Vol Pack Vol Pack
5 US gal 3.75 US gal 6 US gal 1.25 US gal 1.5 US gal

All components are supplied in one 6 US gallon container (part B is supplied in a plastic bag which is suspended above the colour base in a plastic tray). For availability of other unit sizes consult International Paint

Unit shipping weight

Unit size Unit Weight
5 US gal 85.5 lb

Storage

Shelf Life 12 months minimum from date of manufacture when maintained in protected storage at 4-38° C. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Яндекс.Метрика